An efficient internet connection is essential when carrying out some important work online. Whether you use cellular or WiFi, an efficient data transfer is essential to accomplish your tasks efficiently. Laptops with a WiFi connection can often experience connectivity issues. One problem can be that your Laptop disconnects from WiFi often.
Most of the time, it’s not a mistake! It’s normal that your Laptop could be removed from the WiFi network when outside of your router or hotspot range, and it’s the same consequence if you don’t leave your Laptop for a long time allow it to go into sleep mode.
But, you’re aware of an issue when your Laptop stops connecting to WiFi too often, even if you’re near the router and are using the PC.
This article was written to explain the reasons behind Laptop Keep Disconnecting To WiFi and the solutions you could try today. We’ve listed the cause briefly and explained how to fix the Laptop that is constantly disconnecting from the WiFi problem.
Why is My Laptop Keep Disconnecting To WiFi?
Your Laptop could be frequently disconnected from WiFi as you could use an incorrect or obsolete network driver. It is recommended that you don’t rule out the possibility of a hardware malfunction on your Laptop or your router.
This could be why a laptop may disconnect from WiFi, but not always about the particular error.
- The Laptop’s WiFi sensor is trying to connect to a more reliable network, but it cannot connect to the best networks that are within reach.
- This WiFi network driver might be out of date.
- Your Windows may require a new version.
- Laptop power management systems can shut down the network hardware in order to cut down on the power consumption.
- The WiFi card could be damaged,
- Wireless Adapter is not correctly set up, and the frequency range of the channel is not being detected.
- It could be the router’s hardware is damaged, isn’t functioning well, or it isn’t in the right range.
If you do your research, there’s plenty to blame for this connectivity issue on the Laptop. Although that’s the case, there are many reasons to determine the root reason. In addition to the obvious, it may be something other than the scope of this list.
However, the solution will be more straightforward if you are aware of the reason behind it. Then, you can try all the solutions and decide which one works best for you the most. Should it not work, then there could be more things to investigate and tweak before getting back to normal.
However, it’s completely your decision if you’d prefer to follow them or not.
- Always keep a backup of your data: It is always a good idea to keep a backup of your data before you start to back up the essential information in the event that anything goes wrong. Most importantly, you’ll want to backup your C Users.
- Change to an admin Account: Administrative rights are needed to make specific changes to your system, so if you’re using local accounts, change to an administrator account.
When the backup process is completed and the permissions have been elevated. After that, you must follow the steps in the hierarchy of steps to fix your Laptop’s issue of not connecting to WiFi.
How do I solve a Laptop that isn’t connecting to WiFi?
Troubleshooting the Network
Investigating the issue, not just for this specific issue but for most of the problems with laptop network connectivity, first, we must troubleshoot the connectivity.
A lot of the time, this doesn’t give you an immediate answer, but you can do it if it is true, and that could save you a lot of time. You can now go on to…
- Look up troubleshooting in the search bar in the Taskbar. (for Windows 10)
- Open troubleshooting settings.
- Then, click on the Additional troubleshooting link.
- On the next screen, In the next window, click Internet Connections to open the troubleshooter that is specifically designed for you.
If the troubleshooter provides you with some sort of quick fix, apply it and see if it resolves the Laptop’s disconnect from WiFi. If not, move on through the steps.
Change profile on the network
Next, check your network profile settings. Modifying the settings for your network profile resets the connection. Testing the WiFi network in different settings for visibility makes sense. Most of the time, the Windows network profile, is set to public, but you should switch on the private setting and then see if this will help.
- Select the WiFi symbol on the Windows taskbar.
- There will be properties within your network. Click on it to open.
- Next, go to the Network Profile and choose Private, which means that your PC is able to be found by the network you normally connect to.
- After changing the settings for your profile, you should check whether the connection is stable. If not, you can move on to the next step.
Disable the WiFi Sense feature
This feature was created to pick the top networks available on the Laptop’s network automatically. Because it connects to the best networks on its own, the possibility of disconnecting each time it changes networks in the event that the range in question has several networks. The WiFi sense may be confused when the strength of the network changes for several local WiFi routers. It is, therefore, sometimes recommended to disable the WiFi sense feature.
NOTE: The 2021 version for Windows 10’s 1803 version will not support WiFi Sense.
- Navigate to Settings, then click Network and Internet.
- After that, go to WiFi and select Settings for WiFi.
- Scroll down to WiFi and select WiFi Sense and then turn off WiFi Sense. Turn off the connection to the network that is shared by the contacts I have.
- Restart your computer if necessary and verify the WiFi connectivity status.
If turning off the WiFi connection does not resolve the Laptop’s disconnecting from the WiFi issue, you should focus on the subsequent step.
Turn off Random Hardware Access
If you’re not connected to WiFi networks, the PC scans for WiFi networks within the region to assist you in getting connected. You can enable randomly assigned hardware address to conceal your identity from others and keeps trackers off when your PC searches for networks and then connects.
However, the randomness of hardware addresses may cause the delusion that the connection is working, leading to frequent problems with connectivity only when there’s an issue of compatibility between the Laptop’s WiFi router and router hardware. Therefore, it is recommended to keep this feature off.
To disable it:
- Set up WiFi in the Open Settings.
- Check to see if you have the setting for WiFi’s random hardware addresses disabled.
- After the settings have been changed after that, switch your device to air mode for a few seconds to refresh, and then check the WiFi connection again. If it doesn’t work, go through the other solutions step-by-step.
Enable Power Saving on WiFi
If your Laptop is set to go into power-saving mode when the Laptop is running on battery power, your wireless adapter could be in a sleep state. This is a common feature of laptops that reduces energy consumption since wireless network adapters require less power and operate at the right time to receive the network traffic coming through the router.
This can be beneficial for effective power management. However, it can result in unreliability to sustain connections, which means that the Laptop is constantly disconnected from WiFi problems. For this to be fixed,
- Search for device manager in Taskbar.
- Double-click your adapter’s name from the dropdown menu for the Network adapters.
- Select then the Power Management tab and remove the checkmark of allowing your computer to shut down this device to conserve energy, and then click OK.
- Restart and test your internet connection.
Change Power Plan setting.
If you’re connected to WiFi that uses wireless routers or wireless APs that don’t use 802.11 power save, 802.11 power-saving protocol problems with WiFi connectivity could occur.
If the power-saving feature that is included in Windows is making your Laptop disconnect from WiFi, setting the Laptop to maximum performance will help you get rid of this issue.
The following applies to laptops that have been set to utilize the balanced power plan (by default):
- If the Laptop is connected to power, then the wireless adapter for the network is set to utilize the Maximum Performance mode. This shuts off 802.11, the power-saving mode.
- If the Laptop is operating on battery power, The wireless network adapter operates in medium power-saving mode. This mode is connected to the 802.11 power-saving modes.
Therefore, changing your plan of power to maximum performance in both plugged-in as well as battery mode is sensible. But, be aware that your battery will be drained more quickly in the case of maximum performance; therefore, you should try this setting and make sure that you revert the settings in case it doesn’t fix the issue.
- Navigate to the system via Settings in the”Start Menu.
- Go to Extra Power Settings within the Power and Sleep section.
- Simply click on it to change the settings of the plan you’ve chosen.
- Select the button to alter advanced settings.
- Connect to the Wireless Adapter Settings>> Power saving mode>> On Battery Maximum Performance and Connected the highest performance.
- Click Apply, after which click OK and then test the website.
The Network Socket as well as the IP Reset
The 2nd option is resetting the IP and Sockets. Simply put, it restores all settings related to networks to their default settings. This will reset every network configuration. Nearly everything that is under Network and Internet options will be restored to the default settings.
You can utilize to use the netsh command at the Windows command prompt to restore the protocol to default. It resolves major issues with browsing and issues with network connectivity, such as the case where the WiFi adapter discovers a network but is unable to accept the TCP/IP address.
To reset the Network Socket and IP, follow these steps:
- Open CMD.
- Click on the Command Prompt and select ‘Run as an Administrator.’
- If you want to reset your network adapter to a previous state, enter ” netsh winsock reset” and press Enter.
- Then you need to type ” netsh int IP reset resetlog.txt” and hit enter. It will erase the IP logs on your PC.
- Then type “exit” to exit your command prompt.
- Restart your computer to save changes.
This video accomplishes the same thing.
A few users have reported that this solution worked for them, and you may test it out too. To create an individual DNS configuration, follow these instructions.
- Start by going to Start>Settings, then Network and Internet.
- Scroll down to locate the Change Adapter Options.
- Just right-click on the WiFi adapter.
- Click Properties, double-click Internet Protocol Version 4 (TCP/IPv4).
- Select to use manual DNS.
- Enter 1 1 1 1 in a preferred DNS server and 1 zero in the Alternate DNS server. You can also use Google’s public DNS 8 8.8 8 8.8 and 4 4 for both the preferred as well as alternate DNS servers.
- Test your WiFi connection.
Check out WLAN services.
Set the WiFi AutoConfig program so that it starts in a sequence. If the service does not begin when your computer starts, you could experience issues with problems with network connectivity.
- Use Windows + R and enter services.msc and hit OK.
- Scroll down to locate the WLAN Autoconfig.
- Right-click to go to Properties.
- Select the type of Startups Automatic.
- Restart the device and test the connection.
There are different ways you can attempt to solve this problem. You may have tried them… in the event that you didn’t adhere to these guidelines:
Uninstall WiFi Driver
- Use Windows + R and enter devmgmt.msc
- Then, expand the Network Adapter Option, and then click right on the adapter.
- Click on the Uninstall Device button.
- Choose the possibility “Delete drivers software installed on this particular device” and then click uninstall to complete the process.
- After restarting your computer, the system will then install a WiFi driver.
Upgrade WiFi driver
- Look up the Laptop manufacturer’s WiFi driver on Google.
- Visit the official site of the company that manufactures your PC. Find the Laptop’s model.
- You can download the driver using the list by selecting the operating system you are using.
- Install the most recent driver for your Laptop.
Clean up the mess
- Navigate to Settings>Settings Network and Internet > WiFi> Manage Networks You Know About.
- Make sure to highlight and eliminate the problematic network.
- Reboot your computer to test if it displays once more.
- Verifying the Hardware
- Try connecting an Ethernet cable to your router to see if it is compatible.
- Then, plug the Ethernet cable into the modem (if it is not separate) to determine if there is a problem. It could be a problem with the router.
Are you still having trouble getting your Laptop to experience an unbroken WiFi connection?
If despite all the attempts, your Laptop is still disconnected from WiFi and the issue isn’t resolved, then it’s time to contact your Laptop’s corporate support team as well as your router’s support team (if you are the owner of your router). If you have found the answer in this guide, be sure to save the page and return if you encounter the same issue.